Rode NTG3B Moisture-Resistant Shotgun Microphone

• For Indie Films, TV & Documentaries
• Moisture-Resistant for Humid Conditions
• Phantom Powered
• Simple Operation with No Controls
• Enhanced Immunity to RF Interference
• Low-Noise Circuitry
• High Sensitivity Requires Less Gain
• Slight Presence Boost & Bass Attenuation
• Windscreen Reduces Wind Noise
• Lightweight Housing

Rode NTG3 Overview

Capture broadcast-quality sound indoors or outside for your next indie film, TV shoot, or documentary project with the black Rode NTG3B moisture-resistant shotgun microphone. Professional-level features such as low-noise circuitry, upgraded immunity to radio-frequency interference, and minimal handling noise reduce the need to repair and restore audio in postproduction.

The NTG3B's high sensitivity allows it to produce strong output levels without having to apply extreme gain at your mic preamp. Sonically, the NTG3B delivers consistently clear sound due in part to its gentle rise in high frequencies and its rumble-reducing attenuation of low bass frequencies. Its switch- and dial-free design lets you set up quickly and focus on the sound instead of fiddling with various mic settings. The solid brass housing is both durable and lightweight, and its anti-glare finish prevents reflections in the shot.

Designed to Withstand Adverse Environmental Conditions

When your work takes you outdoors, you're bound to encounter humidity and condensation, which can cause many mics to fail. The NTG3B's RF bias technology makes it almost completely resistant to moisture, allowing you to reliably capture high-quality audio in normal and adverse environmental conditions. It also includes a weatherproof aluminum storage cylinder for maximum protection during travel.

Broadcast-Quality Sound

The NTG3B was engineered for broadcast-quality sound, enhanced immunity to RF (radio frequency) interference, and low handling noise. Plus, its balanced output allows longer cable runs than most camera-mount shotgun microphones.

The combination of the NTG3B's 10" long body and supercardioid polar pattern yields focused on-axis directionality with maximum rejection behind the mic. Its low self-noise of 13 dBA and highly sensitive condenser element communicate detailed audio unburdened by the hiss that plagues many low-cost microphones.

Phantom Powered

Thanks to its 3-pin XLR output and compliance with 44 to 52 VDC phantom power, the NTG3B is compatible with a variety of handheld audio recorders, field recorders, and mixer adapters, as well as built-in preamps on many camcorders and cinema cameras.

Ideal for Boompole Mounting

The NTG3B includes a mic clip for easy placement on a mic stand or boompole. Alternatively, mount the NTG3B in the Rode SMR-4 shockmount (available separately) to impede the transfer of vibrations between your boompole and the mic.

Windscreen Minimizes Wind Noise

The NTG3B has a foam windscreen to reduce unwanted wind noise from breezes, fans, heaters, and air conditioners. For maximum reduction of handling noise and wind noise in indoor or outdoor environments, consider the Rode Blimp furry windshield and shockmount suspension system (available separately).

Rode NTG3 Specs

Microphone

Form Factor	Stand/Boom Mount
Sound Field	Mono
Operating Principle	Line Gradient
Capsule	Condenser
Diaphragm	0.5" / 12.70 mm
Polar Pattern	Supercardioid
Orientation	End Address
Circuitry	Solid-State
Pad	None
High-Pass Filter	None
Tone Adjustment	None
Indicators	None
On-Board Controls	None
Windscreen	Foam (Included)

Performance

Frequency Range	40 Hz to 20 kHz
Maximum SPL	130 dB SPL (1 kHz, 1% THD, 1-Kilohm Load)
Off-Axis Rejection	8 dB at 60° 18 dB at 120° 17 dB at 180°
Impedance	25 Ohms
Sensitivity	-30 dBV/Pa at 1 kHz
Output Level	8.2 mV (Max)
Dynamic Range	117 dB
Signal-to-Noise Ratio	81 dB A-Weighted
Equivalent Noise Level	13 dB A-Weighted

Connectivity

Output Connectors (Analog)

1 x XLR 3-Pin

Power

Operating Voltage	48 V ± 4 V
Operating Current Consumption	5 mA

Physical

Color	Black
Mounting	3/8"-16 Female, 5/8"-27 Female, Mic Clip (with Included Hardware)
Construction Material	Brass
Dimensions	ø: 0.75 x L: 10.04" / ø: 19 x L: 255 mm
Weight	5.75 oz / 163 g (Microphone)